Product: taper button bit
If you are looking for more details, kindly visit KSQ Technology.
Taper Degree: 4°46&#;, 6°, 7°, 11° and 12°
Hole Range: 30mm-45mm
Number of Buttons: 6 tips, 7 tips, 8 tips, 9 tips or customized
Button Shape: normally is ballistic button, also available for spherical button
Fitting Rod(socket inside diameter) : 19mm, 22mm or 25mm
Inside Socket Design: normal socket, zinc coating or copper liner
Skirt Length (without tip): 50mm, 55mm, 60mm, 71mm, 80mm or customized
Suitable Machine: hydraulic rock drill, pneumatic jack hammer, gasoline rock drill
Suitable Block: granite and marble
Each of rock drill bit is produced in different sizes and designs in order to optimize their application to a broader scope of rock drilling conditions and correspond to different job requirements.
To ensure the normal service life, taper drill bits need to be matched well with taper drill rods, the taper degree must be the same between taper drill bits and taper dill rods.
&#;Advantages:
Carburized rods give you best in class service life with increased productivity.
Tapered button bits offer extra wear resistance which means lower costs.
Wide assortment & OEM makes it easy to match the need.
Product quality ensures full control over the production tasks.
1. Tapered chisel bits
The tapered chisel bit is widely used in drilling holes with depth less than
5 meters and diameter ranged in 20-45 mm by light-duty rock drill, like Y6.
Diameter
Length
Water hole
Taper degree a=4° 6° 7° 11° 12°
Socket inside diameter d=15, 19, 22, 25
mm
mm
2
20
65
2
23
65
2
25
69
2
28
60
2
30
55 88
2
32
55 64 71 80
2
34
71 80
2
36
74
2
38
74
2
40
74
2
42
74
2
45
74
2
2. Tapered cross bits
The taper cross bits can be used under any rock drilling condition because of it's comprehensive adaptability. Compared with taper chisel bits, taper cross bits have a better drilling performance because carbide tips on cross bits doubled, which means carbides shape are cross type on drill bits. Taper cross bit is mainly used for hard or very hard rock formation.
DescriptionDiameter
Length
Contact us to discuss your requirements of Tapered Rock Drilling Tools. Our experienced sales team can help you identify the options that best suit your needs.
Weight
Taper degree a= 6° 7° 11° 12° Socket inside diameter d=19, 22, 25
mm
mm
kg
28
71 80
0.19
29
71 80
0.2
30
50 67 71 80
0.3
32
50 67 71 80
0.3
33
71 80
0.32
34
67 71 80
0.34
35
67 71 80
0.35
36
71 80
0.36
38
67 71 80
0.42
40
71 80
0.43
41
71
0.45
42
69 80
0.46
44
80
0.47
45
80
0.5
When the right drill bit is in the right ground operated under the right conditions, more core ends up in the box at the end of a shift. There isn&#;t a perfect drill bit matrix or geometry that cuts every ground as quickly as possible. A Longyear bit may cut 17 inches per minute in Arizona, but cut just three inches per minute in Ontario.
Although diamond drill bit selection is often an afterthought, it&#;s just as important as drillers deciding how much water/mud to run or how fast to spin rods.
There are many factors to consider when selecting a drill bit, including the main objective of a project. As mentioned, the overarching objective is always more core in the box, but there are additional elements that need to be considered. For example, a rod trip takes significantly less time at 400 feet than a rod trip at 4,000 feet. While bit life is important, it&#;s less crucial at the top of a hole because that usually means sacrificing penetration rates.
In Australia, a site used two different bits at different depths. A Longyear Red Express bit was used to cut 60 centimeters per meter with a life of only 120 meters at the top of the hole. Once that bit was done they switched to a Longyear Yellow Stage 3, because rod tripping took too long. With this bit they only cut at 35 centimeters per minute but achieved a life of 300 meters per bit. Using a singular Longyear bit, this site put 6% more core in the box than they did with a competitor&#;s bit. However, using these two Longyear bits in tandem, they saw a 23% increase of core in the box over the competitor&#;s product. Sometimes, it&#;s more beneficial to cut faster even if it means tripping more.
Once a driller decides whether the objective is cutting faster or tripping less often, next it&#;s important to establish how hard the ground is to cut. Contrary to popular belief, the ground drillers cut is (probably) not the hardest ground on earth. This is where the Mohs scale comes into play. The Mohs scale is an exponential scale from 1 to 10 to quantify mineral hardness. Minerals with a higher Mohs hardness will scratch anything with a lower Mohs hardness. For example, a mineral classified as a four will scratch a three but not a five.
All the bits offered on the market today are targeting a specific range of the Mohs scale for the best performance. To determine the Mohs hardness of the rock to be drilled, a Mohs hardness scratch test kit is needed. This kit is a series of picks made of different materials that, when used properly, can determine the Mohs hardness plus or minus 0.5.
The Boart Longyear scratch test kit has four scratchers with eight replaceable tips and a sharpening stone. If the numbered tip scratches the rock, the rock is softer than the number on the tip. If a seven scratches and a six doesn&#;t, you know you&#;re in 6.5 rock. You would then select the bit created for that rock.
Once ground hardness is identified, Boart Longyear offers a Longyear Diamond Bits Hardness Rating & Comparison Chart to find a recommended bit for that ground. For example, Purple is meant for 1 - 4.5 rock, up to Red which is best for 7.5 &#; 9. Purple covers such a large range numerically because the Mohs scale is exponential (1 and 4.5 on the Mohs scale are closer together on &#;true&#; hardness than 7.5 and 9).
In the cross reference above, bit range overlaps, and the bars representing each drill bit are quite long. This is where the objectives of the site come into play. For example, if you are in a 6.5 rock, select a Green Bit or a Yellow Bit. Which one should you try first? It depends. If the site is cutting a lot of short holes and bit life isn&#;t a big concern, you would likely have the best luck with Yellow &#; it would penetrate faster than Green, but not have as long of life in 6.5 rock. On the flip side, if bit life is a concern because you&#;re drilling deep holes, you may prefer Green.
Another thing to consider for bit selection is geometry. While the Green bit is, in general, tougher than the Yellow, a Green bit with more open area and a Yellow with less open area will exhibit very similar cutting characteristics.
The geometries offered by Boart Longyear are all designed to cut a little differently. Within each color bar, the Express has the ability to cut harder rock than the Stage and the Stage will cut harder rock than the Tapered Waterway. This is a result of what is called, &#;open area&#;.
Open area is determined by finding the surface area of a disc with the same outside diameter and inside diameter as the drill bit, and subtracting the surface area of the drill bit with all the waterways cut in. What&#;s left is the area of the waterways, flutes, and rounds, and the percentage of this number compared to the area of the total disc is the open area. Express has an open area of 30%, Tapered Waterway has an open area of 25% and Stage has an open area of 20%.
Once the ideal bit has been identified &#; it needs to be tested, and the only way to make an informed decision during testing is to collect data.
Here are three mandatory data points to collect:
&#; Penetration rate on every run
&#; Mohs hardness every run
&#; Bit life of every bit
Once the data has been collected, this information can be used to either validate the choice initially made or adapt based on unaccounted circumstances. For example, if the Green Stage bit was selected but the penetration rate wasn&#;t as high as expected, then the Green Express and the Yellow Stage would be good bits to try next. The Yellow Stage may not provide the desired life, but the Green Express may be a perfect in-between. All this shows in the data and at the end of the day more core ends up in the box.
With a combination of knowledge, the right tools, and good planning, every shift can be optimized, and subsequently, put as much core in the box as possible.
Are you interested in learning more about Rotary Drilling Tools? Contact us today to secure an expert consultation!