Quote from: hopfenundmalz on October 28, , 09:15:51 pmI worked at a commercial brewery as a professional Brewer and I can tell you that we didn&#;t take apart our valves every brew day some of the valves are very hard to get and we took them apart every six months for cleaning for the reasons that you stated and we a lot of piping that had elbows they would have an accumulation in the bends. we followed the procedure very similar to what you talked about above with an oxidizer or PBW followed by a high temperature rinse and before each brew day we recirculated 200° water through the piping on the cold side for approximately 45 minutes that is a sterilization temperature and will kill beer spoilage organisms. So I would recommend continuing what you&#;re doing and taking apart your valves twice a year to give them a good scrubbing and replace the software as needed.Have you considered puting it in an autoclave/pressure cooker to kill bugs?First, I don't have an autoclave. Second, I never considered pressure cooker, but am wary of over heating and damaging the PTFE, seals, etc. I'd need to check spec sheets specifically, but I think most of these lower cost valves are rated somwhere in the ~240 - 260F range, and an autoclave with steam splits the difference.
Brew day post-brew cleaning is an extended recirculation with PBR followed by 200F water and a final sanitizer rinse through the system. I've measured 190+ sustained surface temp on valves, which ought to sanitize their interiors sufficiently---in effect similar to your autoclave/pressure cooker at lower temp.
It's the gunk build-up that occurs with valves where the ball chamber isn't fully encapsulated that concerns me. If there is anything growing on the accumulation, my approach might not be sufficient to knock it down. An extended trip in an autoclave would solve that, subject to the caveats above, but still leave the gunk behind.
Personally, I like to strip down valves every six or so brew days to clean out any gunk and prevent accumulation. Actually, I have my sons do it as part of brewing with me --- those who would drink must work.
I worked at a commercial brewery as a professional Brewer and I can tell you that we didn&#;t take apart our valves every brew day some of the valves are very hard to get and we took them apart every six months for cleaning for the reasons that you stated and we a lot of piping that had elbows they would have an accumulation in the bends. we followed the procedure very similar to what you talked about above with an oxidizer or PBW followed by a high temperature rinse and before each brew day we recirculated 200° water through the piping on the cold side for approximately 45 minutes that is a sterilization temperature and will kill beer spoilage organisms. So I would recommend continuing what you&#;re doing and taking apart your valves twice a year to give them a good scrubbing and replace the software as needed.Sent from my iPhone using Tapatalk Pro
If you want to learn more, please visit our website Xiangyu.
Good industrial valve manufacturers can be hard to find, especially if you&#;re looking for customized features or specialized valves. Here are some of the things you should consider when choosing the right industrial valve manufacturer.
It is important to see where the valve manufacturer has their factory and offices before you decide to buy valves from them. You may want to visit the factory or their office to see the valves in action. This is especially true when placing bulk orders. The location of the company is also important to judge the time and cost of shipping for your order.
Good industrial valve manufacturers invest in getting quality certifications for their products. Internationally acceptable standards like ISO, CE, API, TS and more are good parameters to see if a company manufactures high-quality valves. Certifications are even more important when you are looking for specialized valves like those used in nuclear power plants. Check to see if a company has all the relevant certifications before placing your order.
Are you interested in learning more about China 3 Way Ball Valve Supplier? Contact us today to secure an expert consultation!
Since industrial valves have to be used in many different kinds of factories and work environments, they need to be safety tested to check their performance and longevity. Good valve manufacturers put their valves through a number of safety checks to ensure the valves can work under severe temperature and pressure situations. Be sure to ask the manufacturer about their safety tests and parameters before deciding to buy valves from them.
Good industrial valve manufacturers offer some level of OEM support and customization to their clients. The customization can be general like different actuation options for the valves. Or it could be more specific like fireproofing a certain valve. Greater OEM support means you have more control over the type of valve you can get from a particular company. This is especially important when you are looking for specialized valves.
Just like in any other industry, customer service is uber important in industrial valve industry as well. Leading industrial valve manufacturers have a customer support staff that is ready to answer any queries as soon as possible. Good companies also invest in after-sale services like valve maintenance and cleaning to establish long term goodwill with their clients. It is important to choose a company that is responsive, helpful, and available to help.
Leading industrial valve manufacturers don&#;t just house a variety of new and improved valves but they invest in research and development and building lasting relationships with their clients. Choose a manufacturer that offers high-quality valves at a competitive rate and whose products are backed by proper certifications and warranties.
If you want to learn more, please visit our website China 3 Way Ball Valve Manufacturer.